Видео

It’s really hard to say without looking at it. My first thought would be a loose wire. The junction boxes on these can be pretty tight. So maybe something came loose when closing the box. Could be a bad panel, but I’ve actually never wired one up that didn’t work.

Awesome! Love hearing the success stories. That’s why I do this 🤗

They are in the video description. But depending on the device they can be kind of hidden. I’ll copy them down here 😊 Link for LED color changing pool Light bulb: amzn.to/42sx8o2 Link for Pool Light Gaskets: amzn.to/3MeH3bk

Yeah. I agree. Typically the pins are on the top. I would have installed this the other way if I had installed it. Unless this brand can’t flip around for some reason. I think some only go through the bolt piece one way and then the pins end up on whatever side that happens to be depending on which side of the door the handle is on.

Nice work! I love hearing the success stories. Yeah, often times the hardest part is removing the old one. They can be pretty stuck on there. These faucets are great. It should last you a very long time. Well done 👍🏻

Yeah. That was my thought too. I’ve seen some people say it’s could damage something. So I mentioned it in the video to try to head off any comments. lol. I think it works great. And it is very stable.

The power line coming into the junction box should have a ground wire in it. There should be a black (hot), white (neutral) and an uninsulated (ground). often times the ground is screwed to the back of the junction box if it’s a metal box. That would ground the whole fixture. If it’s a plastic box, then the ground should connect to either the ground wire of the fixture (if there is one) or to a metal screw or something metal about the fixture.

I believe the code here states that outlets near water sources need GFCI outlets, however the washing machine is an exception. I’m not really sure why. Either the washing machine doesn’t count as a water source, or since it’s behind the machine they don’t expect people to be using wet hands to plug things in it.

@@RoscoReviews which NEC year are you on? NEC 210.8(A)(10) requires GFCI in laundry areas since the 2014 revision. I checked w the NFPA and they indicate only 1 state is so far behind that they’re not covered. The NFPA also states that that state is currently in process to update to the 2020 code. So all that in mind, I think you’re very likely incorrect here and need to change that outlet.

You are probably right. I don’t own the property that this was located in. I just do the work that I’m told to. The property is older than 2014 so as far as code goes, it is probably currently grandfathered in to whatever it was at the time it was built unless you do major renovations that would require it to be brought up to current.

@@RoscoReviews I’ve never met an inspector that gave a rats when your house was build. Not when it comes to something as easy as a gfci. All that said it’s not your job to fix if it’s not your property. 🤷‍♂️

You can run a second screen off of the USBC. I would probably use the other one on the MAC and leave the ports on the dock open though.

The anchors screw down to be flush with the top of the concrete when they are not in use.

It’s tough to say without looking at it. If nothing is working then it sounds like the issue isn’t with the remote. But it could be anything.

😂 That is a really good question. It seems like someone should have figured this out by now.

Glad I could help!

No problem 🤗 happy to help!

Awesome!!

No problem! Happy to help :)

I have bought these an amazon and they are pretty good and reasonably inexpensive. amzn.to/4eJYmgq

@@RoscoReviews Thank you for the prompt response

I would try to contact starlink directly. But I’m not sure what countries it’s available in.

If the rod keeps spinning and the slats don’t turn, then it sounds like the issue is in the gear box that the rod connects to. It’s probably fixable, but it’s tough to say exactly what is wrong without looking at it.

Haha. Yep, it’s just that way sometimes.

Wow!! It’s amazing what some people try to charge.

The freezer regularly defrosts itself and drains the water down a tube in the back wall. The tube can get frozen and clogged not allowing the water to drain properly. By leaving the fridge off for a day with the doors open it allows the tube to thaw out so it can drain water again.

I kind of like these over the traditional flappers. I never really liked having to adjust the chain.

I actually rarely use the remote. If it works the same way as the pool lights, you can switch between the colors by toggling it off and back on. Flipping the switch on and off a few times until you reach the desired color.

yeah, that is a chore. I have only had one get clogged once that wasn't just ice. Somehow someone got a piece of corn in there. I don't even know how they did that. lol I used a Co2 cartridge air gun thing that I use to clear out air conditioner condensation lines. and it shot the clog out.

Interesting. I’ve used both, but I haven’t had an issue with one leaking into the cup part. I suppose that is something to consider. I have done a lot more of them with the large nut. The only problem with those is they can be a little bit tricky to tighten if you don’t have a spanner wrench.

I didn’t have to switch them, but it might be worth double checking your plug to battery line. Sometimes the quality control can be questionable.

My current blue wave cover I’ve had for 6 years and it still looks great. I think you will be happy with it.

Happy to help!

It’s tough to say without looking at it. I would probably hold it underwater and turn it all different directions and see if you can see where an air bubble comes out. If you have put a new gasket on the lens and it is still filling with water, it may be leaking somewhere else.

@@RoscoReviews tried pretty much everything at this point except replacing entire assembly;( which will be my next step. Yeah you can't see any bubbles it is super weak leak takes months to see some water buildup inside

The handle locks, then the side that comes off is probably the inside hat you can’t get too. You can sometimes jimmy the door with a card like an old credit card and push the latch enough to open the door.

It’s probably ok. Let it dry out really good. Then put it back together. You can use some vaseline or plumbing silicone grease to help get a seal.

@@RoscoReviews I did end up using plumbers grease this time but I think what helped most was u explaining lining up the writing on the bulb and ring….made it easier to put clamp ring on….i dunked it and it’s water tight, my light is lower than yours so i have a 25lb weight to tie off to my belt and goggles….so now for the hard part that last screw

You can speed up the process by removing the back panel in the freezer and hitting the drain with a hairdryer. Then you are only without a freezer for about 30 minutes. But it’s a bit more work.

Glad it was helpful!

Happy to help :)

You're welcome!

I have seen it do that when it’s coming off the wall or something. But it corrects itself pretty quick.

yes. You can run them in a string.

@@RoscoReviews Thank you very much!!!

That should work. it would definitely be an easy fix like that. I does give an extra joint were it could leak in the future though.

the remote and the opener need to be the same brand. I think some brands may work with each other, but I know if you try to use Genie remotes with a liftmaster opener they won't work.

Interesting, I have never noticed mine making any noise. I'm sorry, I don't think I can help without looking at it. I would think either something is restricting the flow, or maybe its getting air in ti somewhere.

Glad to hear it! It’s amazing what people charge for this. Lol

I have about 80 or so of these whirlpool refrigerators and this is the only time one has ever filled the inside of the wall like this.

Thanks for your solution.

Awesome!! I love hearing the success stories!

It may be tough to see in the video, but the drain tube for this washer is in the recessed box with the valves. It hard to answer how to adapt your setup without looking at it, but if you have a recessed box and the valves still stick out a couple of inches, I would think you could change that. However it may mean cutting into the wall to change how the pipe comes into the box.

I would think sturdy wire cutters or bolt cutters would do it. You could probably also use an angle grinder or, in a pinch, a hack saw.

@@RoscoReviews Thanks, I’m going to try one of those because that wire is not showing any signs of being cut strong stuff 😳🫣

Yeah, there are different gauges for sure. This one is in an apartment. So I’m sure it wasn’t top shelf material. lol

It’s tough to say without looking at it. I do know that brand matters. For instance, if you have a genie motor and a Liftmaster remote, I don’t think they will pair.

Unfortunately, if the screw is rusted, stuck, or stripped out where you cant remove it. If it were me, the next step would be to drill it out. or at least drill off the head of the screw so you can get the light out. then you might be able to get ahold of what's left with some vice grips. The downside is, in order to drill it, you would have to drain the pool down far enough to get a drill to it.